FB pixel

How to use a Breadboard

Published

With the amount of fully functional development boards out there, it’s possible that you won’t use a breadboard very often. However, if you spend enough time in electronics, it’s bound to happen sooner or later. While breadboards are fairly easy to use, a brief overview can reduce that learning curve to 0.

Breadboard Features

Different breadboard sizes - mini, half, full, and full size with metal plate and binding posts.
Different breadboard sizes - mini, half, full, and full size with metal plate and binding posts.

Breadboards come in different sizes and as they get bigger, they generally have a few more features. But there are a couple things that all breadboards have in common:

They’re a grid of holes separated by .1”

Holes in a row or column are separated by 0.1" pitch which is perfect for DIP devices.
Holes in a row or column are separated by 0.1" pitch which is perfect for DIP devices.
  • This gives them a standard separation in each direction. This is helpful for many things but particularly ICs. If you notice with Dual-Inline Package (DIP) IC’s, they’re perfectly sized to fit into breadboards. Breadboards almost always have a center gap as well, which accounts for the separation of the two sides of a DIP IC.

As part of a grid, they have Rows

Holes on each side of a row are all internally connected.
Holes on each side of a row are all internally connected.
  • A series of electrically connected holes. The rows are also separated in the middle.

They also have Columns

The holes within a column are not connected to each other.
The holes within a column are not connected to each other.
  • Columns are not connected to each other. All the holes are separated by a tenth of an inch, so .1” pitch. This is standard because when you start using larger chips, like integrated circuits, the DIP packages fit right into the breadboards.

You can specify a hole using the row number and column letter.

Breadboards use letter for columns and number for rows to specify a hole.
Breadboards use letter for columns and number for rows to specify a hole.
  • Using the number for the rows and letters for the columns you can specify a hole much like the game Battleship. If you’re interested. Maybe you just really miss playing that game - we won’t judge. More likely, using this method of specifying a hole is helpful when following instructions precisely or when you’re building a more complex breadboard and want to be able to document it properly.

Breadboard

Breadboard with power buses.

Buy Online

FROM OnlineComponents.com

More Features

As you get bigger, there are other features you’ll find:

A full size 830 tie-points breadboard with two buses on each side.
A full size 830 tie-points breadboard with two buses on each side.
  • Buses on the side of the breadboard - commonly used for power and ground. Usually there are two buses on each side of the board. These are not connected side-to-side and they’re also divided in half top to bottom. This is helpful if you want a 5V rail and a 3.3V rail but, in my opinion, annoying otherwise.
  • Some bigger breadboards have a stand and some rubber feet for a good grip. This is cool but the rubber feet sometimes fall off making the breadboard wobbly. It’s a small but annoying thing. If the breadboard has a separate base, they usually have connectors off to the side that make it easier to hook up a power supply using a banana plug.
A full size breadboard with a metal plate and binding posts.
A full size breadboard with a metal plate and binding posts.

Common mistakes or pitfalls

Make sure that the leads of the components will not touch each other unintentionally.
Make sure that the leads of the components will not touch each other unintentionally.
  • Be careful about wires touching where they shouldn’t when they’re plugged in. With long leads, some of your components can touch each other unintentionally. Depending on how permanent your breadboard is and the cost of the components, you could consider trimming the leads to the appropriate length. But, if you do that and then move parts around and they no longer reach, that is an unfortunate frustration.
  • Plugging into the wrong holes connecting things that shouldn’t be connected and not connecting things that should. This seems to be most frequently done with power and ground. Color coding and taking your time will help this.
Insert properly the leads of the components to make sure that they are connected to the terminal strip.
Insert properly the leads of the components to make sure that they are connected to the terminal strip.
  • Not getting the wires all the way in to make contact, they can be tough. While difficult to see, if you pay attention, you can tell if the jumper wire or resistor lead or whatever is actually going in. If you only press it up to the internal contact but don’t get it in, it either won’t work, or worse, will work intermittently, which is incredibly frustrating to debug.
  • Messy breadboards - long, out-of-control jumpers, criss-crossing wires and random placement of components. Messy breadboards with wires all over the place are hard to follow and troubleshoot. Take a breath, take your time, and try and make your breadboard more organized and prettier. And, if possible, color code things.
Graduation Cap

Check Yourself

7 Questions

Graduation Cap

Check Yourself

7 Questions



Bill of Materials


Terms Used


Created with our Friend:

OnlineComponents.com is a leading global authorized distributor of electronic components. Founded in 1999, ...
Learn More

Perks from this friend:

Special Feature With This Friend:

Special Feature
Make Bread with our CircuitBread Toaster!

Get the latest tools and tutorials, fresh from the toaster.

What are you looking for?