Quarter-Wavelength Transmission Line

Quarter-wavelength sections of transmission line play an important role in many systems at radio and optical frequencies. The remarkable properties of open- and short-circuited quarter-wave line are presented in Section 3.16 and should be reviewed before reading further. In this section, we perform a more general analysis, considering not just open- and short-circuit terminations but any terminating impedance, and then we address some applications.

The general expression for the input impedance of a lossless transmission line is (Section 3.15):

Note that when

Subsequently:

Recall that (Section 3.15):

Substituting this expression and then multiplying numerator and denominator by

, one obtains

Thus,

Note that the input impedance is inversely proportional to the load impedance. For this reason, a transmission line of length

quarter-wave inverter or simply as a impedance inverter.

Quarter-wave lines play a very important role in RF engineering. As impedance inverters, they have the useful attribute of transforming small impedances into large impedances, and vice-versa – we’ll come back to this idea later in this section. First, let’s consider how quarter-wave lines are used for impedance matching. Look what happens when we solve Equation 3.19.5 for

This equation indicates that we may match the load

to a source impedance (represented by

) simply by making the characteristic impedance equal to the value given by the above expression and setting the length to

. The scheme is shown in Figure 3.19.1.

Figure 3.19.1: Impedance-matching a complex-valued load impedance using quarter-wavelength transmission line.

Exercise

300-to-50Ω match using an quarter-wave section of line.

Design a transmission line segment that matches

at 10 GHz using a quarter-wave match. Assume microstrip line for which propagation occurs with wavelength 60% that of free space.

Solution

The line is completely specified given its characteristic impedance

and length

. The length should be one-quarter wavelength with respect to the signal propagating in the line. The free-space wavelength

at 10 GHz is

cm. Therefore, the wavelength of the signal in the line is

cm, and the length of the line should be

mm.

The characteristic impedance is given by Equation 3.19.6:

This value would be used to determine the width of the microstrip line, as discussed in Section 3.11.

It should be noted that for this scheme to yield a real-valued characteristic impedance, the product of the source and load impedances must be a real-valued number. In particular, this method is not suitable if

has a significant imaginary-valued component and matching to a real-valued source impedance is desired. One possible workaround in this case is the two-stage strategy shown in Figure 3.19.2. In this scheme, the load impedance is first transformed to a real-valued impedance using a length

of transmission line. This is accomplished using Equation 3.19.1 (quite simple using a numerical search) or using the Smith chart (see “Additional Reading” at the end of this section). The characteristic impedance

of this transmission line is not critical and can be selected for convenience. Normally, the smallest value of

is desired. This value will always be less than

since

is periodic in

with period

; i.e., there are two changes in the sign of the imaginary component of

is increased from zero to

. After eliminating the imaginary component of

in this manner, the real component of the resulting impedance may then be transformed using the quarter-wave matching technique described earlier in this section.

Figure 3.19.2: Impedance-matching a complex-valued load impedance using quarter-wavelength transmission line.

Exercise

Matching a patch antenna to 50Ω.

A particular patch antenna exhibits a source impedance of

. (See “Microstrip antenna” in “Additional Reading” at the end of this section for some optional reading on patch antennas.) Interface this antenna to

using the technique described above. For the section of transmission line adjacent to the patch antenna, use characteristic impedance

. Determine the lengths

and

of the two segments of transmission line, and the characteristic impedance of the second (quarter-wave) segment.

Solution:

The length of the first section of the transmission line (adjacent to the antenna) is determined using Equation 3.19.1:

where

is the phase propagation constant for this section of transmission line and

We seek the value of smallest positive value of

for which the imaginary part of

is zero. This can determined using a Smith chart (see “Additional Reading” at the end of this section) or simply by a few iterations of trial-and-error. Either way we find

which we deem to be close enough to be acceptable. Note that

, where

is the wavelength of the signal in the transmission line. Therefore

The length of the second section of the transmission line, being a quarter-wavelength transformer, should be

. Using Equation 3.19.6, the characteristic impedance

of this section of line should be

Discussion:

The total length of the matching structure is

. A patch antenna would typically have sides of length about

, so the matching structure is nearly as big as the antenna itself. At frequencies where patch antennas are commonly used, and especially at frequencies in the UHF (300–3000 MHz) band, patch antennas are often comparable to the size of the system, so it is not attractive to have the matching structure also require a similar amount of space. Thus, we would be motivated to find a smaller matching structure.

Although quarter-wave matching techniques are generally effective and commonly used, they have one important contraindication, noted above – They often result in structures that are large. That is, any structure which employs a quarter-wave match will be at least

long, and

is typically large compared to the associated electronics. Other transmission line matching techniques – and in particular, single stub matching (Section 3.23) – typically result in structures which are significantly smaller.

The impedance inversion property of quarter-wavelength lines has applications beyond impedance matching. The following example demonstrates one such application:

Exercise

RF/DC decoupling in transistor amplifiers.

Transistor amplifiers for RF applications often receive DC current at the same terminal which delivers the amplified RF signal, as shown in Figure 3.19.3. The power supply typically has a low output impedance. If the power supply is directly connected to the transistor, then the RF will flow predominantly in the direction of the power supply as opposed to following the desired path, which exhibits a higher impedance. This can be addressed using an inductor in series with the power supply output. This works because the inductor exhibits low impedance at DC and high impedance at RF. Unfortunately, discrete inductors are often not practical at high RF frequencies. This is because practical inductors also exhibit parallel capacitance, which tends to decrease impedance.

Figure 3.19.3: Use of an inductor to decouple the DC input power from the RF output signal at the output of a common-emitter RF amplifier.

Solution:

A solution is to replace the inductor with a transmission line having length

as shown in Figure 3.19.4. A wavelength at DC is infinite, so the transmission line is essentially transparent to the power supply. At radio frequencies, the line transforms the low impedance of the power supply to an impedance that is very large relative to the impedance of the desired RF path. Furthermore, transmission lines on printed circuit boards are much cheaper than discrete inductors (and are always in stock!).