FB pixel

The Biot-Savart Law

LEARNING OBJECTIVES

By the end of this section, you will be able to:

  • Explain how to derive a magnetic field from an arbitrary current in a line segment
  • Calculate magnetic field from the Biot-Savart law in specific geometries, such as a current in a line and a current in a circular arc

We have seen that mass produces a gravitational field and also interacts with that field. Charge produces an electric field and also interacts with that field. Since moving charge (that is, current) interacts with a magnetic field, we might expect that it also creates that field—and it does.

The equation used to calculate the magnetic field produced by a current is known as the Biot-Savart law. It is an empirical law named in honor of two scientists who investigated the interaction between a straight, current-carrying wire and a permanent magnet. This law enables us to calculate the magnitude and direction of the magnetic field produced by a current in a wire. The Biot-Savart law states that at any point

(Figure 9.1.1), the magnetic field

due to an element

of a current-carrying wire is given by

Current element
Figure 9.1.1 A current element

produces a magnetic field at point P given by the Biot-Savart law.



The constant

is known as the permeability of free space and is exactly

(9.1.2)

in the SI system. The infinitesimal wire segment

is in the same direction as the current

(assumed positive),

is the distance from

to

and

is a unit vector that points from

to

, as shown in the figure.The direction of

is determined by applying the right-hand rule to the vector product

. The magnitude of

is

(9.1.3)

where

is the angle between

and

. Notice that if

, then

. The field produced by a current element

has no component parallel to

.

The magnetic field due to a finite length of current-carrying wire is found by integrating Equation 9.1.3 along the wire, giving us the usual form of the Biot-Savart law.

BIOT-SAVART LAW

The magnetic field

due to an element

of a current-carrying wire is given by

(9.1.4)



Since this is a vector integral, contributions from different current elements may not point in the same direction. Consequently, the integral is often difficult to evaluate, even for fairly simple geometries. The following strategy may be helpful.



Problem-Solving Strategy: Solving Biot-Savart Problems

To solve Biot-Savart law problems, the following steps are helpful:

  1. Identify that the Biot-Savart law is the chosen method to solve the given problem. If there is symmetry in the problem comparing and , Ampère’s law may be the preferred method to solve the question.
  2. Draw the current element length and the unit vector , noting that points in the direction of the current and points from the current element toward the point where the field is desired.
  3. Calculate the cross product . The resultant vector gives the direction of the magnetic field according to the Biot-Savart law.
  4. Use Equation 9.1.4 and substitute all given quantities into the expression to solve for the magnetic field. Note all variables that remain constant over the entire length of the wire may be factored out of the integration.
  5. Use the right-hand rule to verify the direction of the magnetic field produced from the current or to write down the direction of the magnetic field if only the magnitude was solved for in the previous part.

EXAMPLE 9.1.1

Calculating Magnetic Fields of Short Current Segments

A short wire of length

carries a current of

in the vertical direction (Figure 9.1.2). The rest of the wire is shielded so it does not add to the magnetic field produced by the wire. Calculate the magnetic field at point

, which is

from the wire in the

-direction.

(Figure 9.1.2)



Figure 9.1.2 A small line segment carries a current I in the vertical direction. What is the magnetic field at a distance x from the segment?



Strategy

We can determine the magnetic field at point

using the Biot-Savart law. Since the current segment is much smaller than the distance

, we can drop the integral from the expression. The integration is converted back into a summation, but only for small

, which we now write as

. Another way to think about it is that each of the radius values is nearly the same, no matter where the current element is on the line segment, if

is small compared to

. The angle

is calculated using a tangent function. Using the numbers given, we can calculate the magnetic field at

.



Solution

The angle between

and

is calculated from trigonometry, knowing the distances

and

from the problem:


The magnetic field at point

is calculated by the Biot-Savart law:

From the right-hand rule and the Biot-Savart law, the field is directed into the page.



Significance

This approximation is only good if the length of the line segment is very small compared to the distance from the current element to the point. If not, the integral form of the Biot-Savart law must be used over the entire line segment to calculate the magnetic field.

CHECK YOUR UNDERSTANDING 9.1

Using Example 9.1.1, at what distance would

have to be to measure a magnetic field half of the given answer?

EXAMPLE 9.1.2

Calculating Magnetic Field of a Circular Arc of Wire

A wire carries a current

in a circular arc with radius

swept through an arbitrary angle

(??). Calculate the magnetic field at the centre of this arc at point

.

(Figure 9.1.3)



Figure 9.1.3 A wire segment carrying a current

. The path

and radial direction

are indicated.



Strategy

We can determine the magnetic field at point

using the Biot-Savart law. The radial and path length directions are always at a right angle, so the cross product turns into multiplication. We also know that the distance along the path dl is related to the radius times the angle

(in radians). Then we can pull all constants out of the integration and solve for the magnetic field.



Solution

The Biot-Savart law starts with the following equation:

As we integrate along the arc, all the contributions to the magnetic field are in the same direction (out of the page), so we can work with the magnitude of the field. The cross product turns into multiplication because the path

and the radial direction are perpendicular. We can also substitute the arc length formula,

:

The current and radius can be pulled out of the integral because they are the same regardless of where we are on the path. This leaves only the integral over the angle,

The angle varies on the wire from 0 to θθ; hence, the result is



Significance

The direction of the magnetic field at point

is determined by the right-hand rule, as shown in the previous chapter. If there are other wires in the diagram along with the arc, and you are asked to find the net magnetic field, find each contribution from a wire or arc and add the results by superposition of vectors. Make sure to pay attention to the direction of each contribution. Also note that in a symmetric situation, like a straight or circular wire, contributions from opposite sides of point

cancel each other.

CHECK YOUR UNDERSTANDING 9.2

The wire loop forms a full circle of radius

and current

. What is the magnitude of the magnetic field at the centre?

Candela Citations

CC licensed content, Specific attribution

  • Download for free at http://cnx.org/contents/7a0f9770-1c44-4acd-9920-1cd9a99f2a1e@8.1. Retrieved from: http://cnx.org/contents/7a0f9770-1c44-4acd-9920-1cd9a99f2a1e@8.1. License: CC BY: Attribution
 
 
Use left and right arrow keys to change pagesUse left and right arrow keys to change pages.
Swipe left and right to change pages.\Swipe left and right to change pages.
Make Bread with our CircuitBread Toaster!

Get the latest tools and tutorials, fresh from the toaster.

What are you looking for?